Skip to main content

DIY 3W constant current LED driver

This is quick post about 3W constant current LED driver which I was design to combine with some homemade furniture piece. The main components of this system is LM311 voltage comparator and IRF9540 P-Channel MOSFET.


Schematic of 3W LED driver module

This module is design to drive maximum of two 3W high power LEDs and it requires 8V - 10V DC (500mA) power source. In this given configuration this module may not need any heat-sink (for IRF9540) and consume maximum of 500mA of power.

Breadboard version of 3W LED driver

At prototyping stages we test this module using 9V DC (1A) power supply with two 3W LEDs (EDEX-3LA1-E1). I developed final version of this module using piece of strip-board and PCB design is not done.
Labels:

Comments

Anonymous said…
nice, and no choke...
1 question though. 3w power leds are rated at 700 ma. why go for 500 ma?
December 27, 2013 at 7:54 PM
Dilshan Jayakody said…
During our tests this system draw 450mA with two 3W LEDs, so we keep minimum current as 500mA.
December 27, 2013 at 8:48 PM
Dilshan Jayakody said…
Schematic is updated to fix some errors:

1. Fix IRF9540 source and drain connections.

2. Add buck switcher output
circuit to IRF9540.
December 29, 2013 at 8:29 AM
Jerome Demers said…
To limit current for my LEDs, I use the LM317 in a "current regulator" mode. It's pretty darn simple! Decoupling cap, a resistor and the LM317.
December 29, 2013 at 10:29 AM
Ben said…
Any thoughts on an led driver for a battery powered applications?

In the past, I've used TI's LM3410 sepic led driver with a aaa (1.5v), but the maximum constant current is about 700ma. I'm hoping to find something that gets closer to 1A.

December 29, 2013 at 11:29 PM
Dilshan Jayakody said…
For high current LED projects I’m using NCL30100 or HV9911 (both are available at eBay).

Liner Technology developed several high current LED drivers (ex: LT3743, LT3476, etc.) but I never used them because these ICs are bit difficult to find in local market place (and even in eBay also).
December 30, 2013 at 7:36 AM
Selvam said…
Hi Dilshan, I am building a battery powered LED torch with 4X1.2V 1200mA batteries, and 3X3W LEDs I am trying hard to find a driver which could do the job of connecting them together
the LEDs I have are,
LED, HIGH POWER, 5000K, 70CRI, 275LM
Series: LUXEON TX
LED Colour: White
Luminous Flux @ Test: 369lm
Forward Current @ Test: 1A
Forward Current If Max: 1.2A
Forward Voltage @ Test: 2.86V.

could you please help me what should be the specifications of the driver??
March 10, 2014 at 6:12 PM
Anonymous said…
Ijust recently came across this web log after doing a google seach for "constant current mosfet and lm311 circuit" hence I have these. and finding this is the most inspirational thing I have found so far! thanks to ALL contributers, I have to go carefuly design, I already made a similar circuit for my 1.8 to 2 watt blue laser, but as the laser still works but the circuit is now getting temprimental, I need to go make some kind of new, and hopefully better circuit. Thanks for this!
June 1, 2020 at 6:46 AM
JeffreyEdwards said…
I really liked your Information. Keep up the good work. Constant Voltage LED Driver
March 25, 2021 at 10:27 PM
Post a Comment

Popular posts from this blog

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist
2 comments
Read more

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle.  In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ
Post a Comment
Read more

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M
5 comments
Read more